Here are the theory test questions for A36 Lorry Loader.
During the theory test you'll be asked a maximum of 40 questions.
Please note that your paper will include all the questions we have marked here with an asterisk *. In addition you will have a random selection of the other questions that are not marked here with an asterisk.
These questions will appear on every A36 paper
Prior to placing loads on to the vehicle bed, explain FOUR items to be taken into account. (4 marks)*
What are the THREE actions or stages that a lorry-loader operator undertakes during pre-use inspections? (2 marks)*
Who only can authorise partial stabiliser extensions and b) what is the effect on lifting capacity if partially extending the outriggers? (3 marks)*
Describe FIVE factors to be taken into account when planning a lift. (5 marks)*
What is the function of a motion limiter? (1 marks)*
Where the loader crane cannot be folded, e.g. when bucket- or clamshell-equipped, what TWO checks must be carried out before the vehicle re-joins the public highway? (4 marks)*
Name FOUR attachments that may be fitted to a lorry loader. (4 marks)*
After unloading brick and block type material from the vehicle bed, what action should the operator carry out before re-joining the public highway? (1 marks)*
Before re-joining the public highway after completing work, what check must be made to the stabilisers? (4 marks)*
What checks should be made to the transmitter of a remote-controlled loader before work? (2 marks)*
What is the purpose of stabilisers on the lorry loader? (1 marks)*
How does the fitting of a clamshell bucket or hydraulic grab affect the lifting capacity of the loader crane. (1 marks)*
a) What should be fitted to the hook of a lorry loader and
b) why? (2 marks)*
If setting up to lift loads in a pedestrianised area, state THREE factors that need to be taken into account. (3 marks)*
If using a lorry loader from a fixed-position operating station, what should be ensured for the safety of the operator? (2 marks)*
A random selection of these questions will appear on each A36 paper
Prior to travelling the machine on the public highway, describe four items to be taken into account when planning a route. (4 marks)
As stamped on lifting accessories, what do the letters SWL signify? (1 marks)
If the words STOP NOW are given to the crane operator by radio during the lift, what action must the operator take? (2 marks)
Give TWO examples of where The Work at Height Regulations may apply to lorry-loader operations. (2 marks)
A lorry loader is working in the vicinity of another crane, encroaching on its operating radius.
What actions need to be taken? (3 marks)
Only two legs of an 8 tonne four-legged chain sling are being used.
What is the maximum load that can be lifted? (1 marks)
If using the help of an assistant when the operator has limited visibility of the landing area, what must be ensured if hand signals are to be used? (1 marks)
What makes up the total (or gross) weight of a load that is to be lifted? (3 marks)
a) Which part of the lorry loader applies loading or pressure to the ground and
b) name TWO ways that pressure can be reduced. (3 marks)
If a load has to be held suspended, what must the operator do? (1 marks)
What information is needed when estimating the weight of a load? (2 marks)
What is the main purpose of the Rated Capacity Indicator (RCI)? (3 marks)
State the functions or job role of the following personnel:
a) appointed person,
b) crane supervisor,
c) slinger,
d) signaller. (4 marks)
Which parts of the lorry loader is the radius (for lifting) measured from? (2 marks)
a) What is meant by a ‘knuckle-boom’ crane and
b) what advantage do they have over straight boom cranes? (2 marks)
Although not best practice, state the possible effect of lifting a load downhill on a slope. (1 marks)
Give FOUR reasons that may cause the lorry loader to overturn. (4 marks)
For vehicles that normally exceed 3 metres in height, what type of warning device must be fitted as a minimum and where? (2 marks)
What are the THREE actions that should be undertaken during pre-use inspections on lifting accessories? (3 marks)
During work, the engine starts to overheat.
Explain the danger if someone tries to remove the radiator or expansion tank cap. (2 marks)
a) When is a trial lift carried out and
b) name THREE checks to be made? (4 marks)
On a construction site with a hard hat requirement, in what situation does a hard hat NOT normally need to be worn on site when using a lorry loader? (2 marks)
If setting up to work near a bank, what is the recommended minimum distance between the stabilisers and the top of the bank? (3 marks)
Name THREE possible underground hazards which may affect the stability of the vehicle during lifting operations. (3 marks)
Polyester webbing slings normally are coloured and have black lines. What do the different colours and number of lines indicate? (2 marks)
Name THREE ways in which wind speed can affect the lifting operation. (3 marks)
If a load is slewed at too high a speed for its size, what TWO factors must the operator take into account? (4 marks)
During the lifting operation, part of the task cannot be carried out as detailed in the lift plan.
a) What initially must happen to the lifting operation and
b) who authorises any changes? (2 marks)
The operator has to use a new attachment that they are unfamiliar with. What do Regulations (i.e. LOLER 98) and other guidance require the operator to have? (3 marks)
The safe working load or working load limit (SWL/WLL) of a multi-leg chain sling only applies in what TWO conditions or configuration? (2 marks)
Name TWO things that happen if a load is not lifted vertically. (1 marks)
When slewing with a load, where should the operator be looking? (1 marks)
Name THREE places where the vehicle should NOT be parked after completion of the lifting operation. (3 marks)
a) What determines the minimum distances that any part of plant and machinery has to be kept from over head electricity lines and
b) explain why a distance should be kept. (4 marks)
Before leaving the cab for a rest break, after parking and switching off the vehicle, what final action must be carried out? (2 marks)
a) What is the minimum distance allowed near open trenches when travelling the lorry loader on a site and
b) explain why? (1 marks)
If checking the oil level using a dipstick, why must gloves be worn? (1 marks)
What information must be found on the loader’s rating plate? (2 marks)
What is meant by centre of gravity, or how is the centre of gravity determined, on a load to be lifted? (1 marks)
a) What is meant by the lifting capacity of the lorry loader and
b) who determines it? (2 marks)
If fitting an extension to the lorry loader, why is it important that the manufacturer's procedures are followed precisely? (2 marks)
End of questions for A36 Lorry Loader
